VTech device

A Novel Power Inverter Design Using GaN Transistors Produces a Power Density of 61.2 W/in3

, , , ,

[Original article published by Power Systems Design Magazine is available here on page 23.]

Details of Virginia Tech’s design that won 3rd place in Google’s Little Box Challenge


Xianan Zhao, Lanhua Zhang and Rachael Born Virginia Tech


In response to Google’s Little Box Challenge (LBC), our Virginia Tech team, the Future Energy Electronics Center (FEEC), decided to design a power inverter. As shown below, our design significantly surpassed the LBC specifications.

VTech top graphic

Our final design exhibited a power density of 61.2 W/in3, exceeding the LBC goal of 50 W/in3 by 22.4%. GaN transistors played a crucial role in our ability to achieve this level of performance1 and ultimately take third place in a field of 2,000 competition entries. This paper details our design approach, and the considerations we made while developing our inverter. We end with suggestions for future designs. GaN transistors were also instrumental in the LBC winning design which produced a power density of 143 W/in3.


Our overall approach was to create a two-stage inverter design: a DC/DC stage that stepped down the voltage and actively canceled the 120 Hz input ripple, followed by a DC/AC stage. Originally we chose an interleaved topology for the DC/AC stage (Fig. 2) consisting of two high frequency legs and one low frequency leg. The modulation of these switches can be seen in Fig 3. Using six 氮化镓系统 (GaN Systems) GS66508P transistors we achieved a peak efficiency of 99.3% with hard switching at 60 kHz in the high frequency leg, and 60 Hz in the low frequency leg.

VA Tech Figure 2 500

Figure 2: Inverter topology without considering power decoupling

VA Tech Figure 3 1000

Figure 3: Modulation strategy

However, when we began to test leakage current we saw a spike near the zero crossing. This would have caused us to fail Google’s initial requirements. To remedy this we changed to a HERIC DC/AC topology (Fig. 4) with a modulation that permitted a non-unity power factor load.

VA Tech figure 4 banner

Figure 4: Switch-level schematic of the FEEC Little Box

Using six GS66516T transistors, this stage reached 98.97% peak efficiency. We selected these devices because they are top-cooled and have a small RDS(on) for higher efficiency.

The enclosure we used was made entirely out of copper. The lid served as the heat sink for the DC/DC stage and the rest of the case served as the heat sink for the DC/AC stage PCB. Originally, we had hoped to reach such a high efficiency that the case-as-heatsink would be enough and we wouldn’t require any forced-air cooling. In the end, however, we added a handful of 0.1W micro-fans for some forced air cooling. The thin, top cooled 氮化镓系统 (GaN Systems) transistors allowed us to place the devices on the bottom of the PCB and directly connect to the case-as-heatsink while the remaining components were populated on the top of the PCB and faced the inside of the box (Fig. 5).

VTech board fig 5 1000

Figure 5: PCB layout

Initially we killed devices attempting to work out the proper gate drive. After this, we only killed one or two transistors, but this occurred under a system-wide failure where several things were broken and the source of the break-down was hard to find.

It took several iterations to arrive at our final gate-driver design for the GaN devices. We finally decided on a Silicon Lab Si8261BAC driver and a custom-designed 12V to 7V isolated power supply for each device. As a consequence of the high speed switching transition of GaN devices, CM noise is easy to couple and interfere with the control circuit. If the control circuit is not well designed, the power switch can be falsely turned on or off. An opto-coupler based gated driver is good for CM noise immunity, but it occupies a lot of space and introduces propagation delay. The Silicon Lab gate driver chip employs an LED emulator as the input stage to be compatible with traditional opto-couplers with smaller volume and shorter delays. But even with the LED emulator as the input stage, the gate driver chip still has the chance to falsely drive the power switch on/off.

To solve this problem, we used a new connection, as shown in Fig. 6 and Fig. 7. Since the gating signals are complimentary, if PWM1A is high and PWM1B is low, U4 is enabled with positive voltage. When PWM1B is high and PWM1A is low, U4 is disabled with negative voltage and the reverse diode of U4 conducts the reverse current. Compared to the case that connects K to ground, the proposed method is more reliable. The effectiveness is also verified by the experimental test.

Figure 6

Figure 6: Gate driver equivalent circuit

Figure 7

Figure 7: Proposed connection for the gate driver

With everything properly designed, the devices were robust enough to pass Google’s 100 hours of testing.


Future Designs Suggestions

From our experience, here are several suggestions for future designs:

  • In the PCB layout, maintain a clear gap between the high and low voltage.
  • Place the High and Low side switches close together to minimize parasitic inductance. The trace connecting to that intersection point should be narrow to help with EMI and system efficiency because it reduces the equivalent output capacitance.
  • Current driving with LED emulator is better than just using a logic signal. This operation is similar to the traditional opto-coupler as it helps to reject noise.
  • Use an anti-parallel diode between A and C on Si8261BAC to conduct current so that the input can be reversed biased (the voltage on A is higher than the voltage on C) to prevent false turn-on.
  • Connect the gate drive ground directly to the source tab to avoid the parasitic inductance in the gate driver loop and to decouple the relationship between the power loop and gate driver loop.